Question 1

While having a discussion, Technician A says that there is a short shaft at the outside end of a drive axle called a stub shaft. Technician B says that is called a stub axle. Who is correct?

Accepted Answer

A)  A only
B)  B only
C)  Both A and B
D)  Neither A nor BE) None of the above
F) B) and C)

Question 2

What are the different ways of classifying CV joints?

Accepted Answer

There are three ways of classi...

Question 3

While having a discussion, Technician A says that in a typical front-wheel-drive transmission, fourth gear would be accomplished by locking the input shaft to the output shaft for a 1:1 ratio. Technician B says that this occurs in a typical rear-wheel-drive transmission. Who is correct?

Accepted Answer

A)  A only
B)  B only
C)  Both A and B
D)  Neither A nor BE) B) and C)
F) A) and C)

Question 4

The term MOST-Likely used to describe the inboard CV joint is:

Accepted Answer

A)  spider gear
B)  hunting gearset
C)  pumpkin
D)  plunge jointE) C) and D)
F) A) and D)

Question 5

The term MOST-Likely used to describe a drive axle is:

Accepted Answer

A)  locking hub
B)  axle shaft
C)  spider gear
D)  drivelineE) C) and D)
F) B) and C)

Question 6

Why is the outboard joint referred to as a fixed joint?

Accepted Answer

It does not change length like an inboard plunge joint. A fixed joint can move up or down and side to side. It also allows sharp side-to-side angle changes during steering, while at the same time allowing the suspension to move up and down as the vehicle moves over bumps in the road.

Question 7

With respect to power, what is the difference between the second gear and the fourth gear?

Accepted Answer

Second gear - Power comes in through the...

Question 8

The inside end of the axle shaft is called the ____________________.

Accepted Answer

The answer of The inside end of the axle shaft...

Question 9

In ____________________ gear, power comes in through the input shaft and leaves through a fixed spur gear.

Accepted Answer

The answer of In ____________________ gear, power comes in through...

Question 10

A(n) ____________________ combines an automatic transmission and a differential.

Accepted Answer

The answer of A(n) ____________________ combines an automatic transmission and...

Question 11

What is the purpose of the two shift cables?

Accepted Answer

One of them moves a selector o...

Question 12

A(n) ____________________ allows the wheels to turn at different speeds when rounding corners.

Accepted Answer

differential

Question 13

In ____, power comes in through the input shaft first gear.

Accepted Answer

A)  low gear
B)  second gear
C)  third gear
D)  fourth gearE) B) and C)
F) C) and D)

Question 14

Which of the following statements is LEAST-Likely true?

Accepted Answer

A)  Most double offset joints are spline-mounted to the transaxle.
B)  A double offset plunge joint has grooves in the bearing races that would cross each other if they extended far enough.
C)  A double offset plunge joint uses six balls evenly spaced by a cage.
D)  A tripod tulip plunge joint has a spider assembly with three spherical rollers that ride on needle bearings.E) C) and D)
F) A) and D)

Question 15

Advantages of rear-wheel drive include reduced weight and a more efficient drivetrain, resulting in better fuel economy.

Accepted Answer

A) True 
 B)False  False

Question 16

In ____, power comes in through the input shaft third gear, which is connected to the input shaft by the third and fourth synchro clutch.

Accepted Answer

A)  low gear
B)  fixed gear
C)  third gear
D)  fourth gearE) All of the above
F) None of the above

Question 17

Which of the following terms LEAST-Likely refers to an output shaft?

Accepted Answer

A)  Drive shaft
B)  Countershaft
C)  Pinion shaft
D)  MainshaftE) A) and B)
F) A) and C)

Question 18

In a typical rear-wheel-drive transmission, fourth gear would be accomplished by locking the input shaft to the output shaft for a 1:1 ratio.

Accepted Answer

A) True 
 B)False

Question 19

A front-wheel-drive car has a transaxle, which combines a transmission and differential into a single unit.

Accepted Answer

A) True 
 B)False

Question 20

Are rear-wheel-drive axles and front-wheel-drive axles the same?

Accepted Answer

Rear-wheel-drive axles and fro...

Exam 77: Front-Wheel-Drive Transaxle and Cv Joint Service

While having a discussion, Technician A says that there is a short shaft at the outside end of a drive axle called a stub shaft. Technician B says that is called a stub axle. Who is correct?

Correct Answer
verified

What are the different ways of classifying CV joints?

Correct Answer
verified
There are three ways of classi...
View Answer

While having a discussion, Technician A says that in a typical front-wheel-drive transmission, fourth gear would be accomplished by locking the input shaft to the output shaft for a 1:1 ratio. Technician B says that this occurs in a typical rear-wheel-drive transmission. Who is correct?

Correct Answer
verified

The term MOST-Likely used to describe the inboard CV joint is:

Correct Answer
verified

The term MOST-Likely used to describe a drive axle is:

Correct Answer
verified

Why is the outboard joint referred to as a fixed joint?

With respect to power, what is the difference between the second gear and the fourth gear?

Correct Answer
verified
Second gear - Power comes in through the...
View Answer

The inside end of the axle shaft is called the ____________________.

Correct Answer
verified

In ____________________ gear, power comes in through the input shaft and leaves through a fixed spur gear.

Correct Answer
verified

A(n) ____________________ combines an automatic transmission and a differential.

Correct Answer
verified

What is the purpose of the two shift cables?

Correct Answer
verified
One of them moves a selector o...
View Answer

A(n) ____________________ allows the wheels to turn at different speeds when rounding corners.

Correct Answer
verified
differential

In ____, power comes in through the input shaft first gear.

Correct Answer
verified

Which of the following statements is LEAST-Likely true?

Correct Answer
verified

Advantages of rear-wheel drive include reduced weight and a more efficient drivetrain, resulting in better fuel economy.

Correct Answer
verified
False

In ____, power comes in through the input shaft third gear, which is connected to the input shaft by the third and fourth synchro clutch.

Correct Answer
verified

Which of the following terms LEAST-Likely refers to an output shaft?

Correct Answer
verified

In a typical rear-wheel-drive transmission, fourth gear would be accomplished by locking the input shaft to the output shaft for a 1:1 ratio.

Correct Answer
verified

A front-wheel-drive car has a transaxle, which combines a transmission and differential into a single unit.

Correct Answer
verified

Are rear-wheel-drive axles and front-wheel-drive axles the same?

Correct Answer
verified
Rear-wheel-drive axles and fro...
View Answer

Exam 77: Front-Wheel-Drive Transaxle and Cv Joint Service

While having a discussion, Technician A says that there is a short shaft at the outside end of a drive axle called a stub shaft. Technician B says that is called a stub axle. Who is correct?

Correct AnswerverifiedShow Answer

What are the different ways of classifying CV joints?

Correct AnswerverifiedThere are three ways of classi...View AnswerShow Answer

While having a discussion, Technician A says that in a typical front-wheel-drive transmission, fourth gear would be accomplished by locking the input shaft to the output shaft for a 1:1 ratio. Technician B says that this occurs in a typical rear-wheel-drive transmission. Who is correct?

Correct AnswerverifiedShow Answer

The term MOST-Likely used to describe the inboard CV joint is:

Correct AnswerverifiedShow Answer

The term MOST-Likely used to describe a drive axle is:

Correct AnswerverifiedShow Answer

Why is the outboard joint referred to as a fixed joint?

With respect to power, what is the difference between the second gear and the fourth gear?

Correct AnswerverifiedSecond gear - Power comes in through the...View AnswerShow Answer

The inside end of the axle shaft is called the ____________________.

Correct AnswerverifiedShow Answer

In ____________________ gear, power comes in through the input shaft and leaves through a fixed spur gear.

Correct AnswerverifiedShow Answer

A(n) ____________________ combines an automatic transmission and a differential.

Correct AnswerverifiedShow Answer

What is the purpose of the two shift cables?

Correct AnswerverifiedOne of them moves a selector o...View AnswerShow Answer

A(n) ____________________ allows the wheels to turn at different speeds when rounding corners.

Correct Answerverifieddifferential

In ____, power comes in through the input shaft first gear.

Correct AnswerverifiedShow Answer

Which of the following statements is LEAST-Likely true?

Correct AnswerverifiedShow Answer

Advantages of rear-wheel drive include reduced weight and a more efficient drivetrain, resulting in better fuel economy.

Correct AnswerverifiedFalse

In ____, power comes in through the input shaft third gear, which is connected to the input shaft by the third and fourth synchro clutch.

Correct AnswerverifiedShow Answer

Which of the following terms LEAST-Likely refers to an output shaft?

Correct AnswerverifiedShow Answer

In a typical rear-wheel-drive transmission, fourth gear would be accomplished by locking the input shaft to the output shaft for a 1:1 ratio.

Correct AnswerverifiedShow Answer

A front-wheel-drive car has a transaxle, which combines a transmission and differential into a single unit.

Correct AnswerverifiedShow Answer

Are rear-wheel-drive axles and front-wheel-drive axles the same?

Correct AnswerverifiedRear-wheel-drive axles and fro...View AnswerShow Answer

Correct Answer
verified

Correct Answer
verified
There are three ways of classi...
View Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
Second gear - Power comes in through the...
View Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
One of them moves a selector o...
View Answer

Correct Answer
verified
differential

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
False

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified
Rear-wheel-drive axles and fro...
View Answer